Search Results

The way In which combustion chamber geometry affects combustion in SI engines was studied using a quasi-diraensional cycle simulation. Calculations were performed to investigate the following questions: (i) the sensitivity of geometric effects on combustion to engine operating conditions; (ii) the differences in burn duration between ten chamber geometries and spark plug locations; and (iii) the relative merits of improved chamber design and amplified turbulence as means to reduce burn duration. The results from these studies are presented and discussed.

The direct injection spark-ignition engine is the only internal combustion engine with the potential to equal the efficiency of the diesel and to tolerate a wide range of fuel types and fuel qualities without deterioration of performance. However, this engine has low combustion efficiency and excessive hydrocarbon emissions when operating at light load. In this paper, potential sources of hydrocarbon emissions during light load operation are postulated and analyzed. The placement of fuel away from the primary combustion process in conjunction with a lack of secondary burnup are isolated as important hydrocarbon emissions mechanisms. Analyses show that increasing cylinder gas temperatures can improve secondary burnup of fuel which would reduce hydrocarbon emissions. Practical means to achieve this include higher compression ratio and use of ceramic parts in the combustion chamber.

A model has been developed for a divided-chamber automotive diesel engine which describes the intake, compression, combustion and expansion, and exhaust processes in sufficient detail to permit calculations of pressure, fuel-air ratio distribution, heat release distribution, NO formation, soot mass loading, and soot oxidation processes. The novel feature of this model is the use of a stochastic mixing approach during the combustion and expansion processes to describe the nonuniform fuel-air ratio distribution within the engine. In this approach, the fuel-air ratio distribution during the combustion and emissions formation processes can be followed as it evolves with time. Experimental data generated on a single-cylinder divided-chamber diesel engine were used to verify the accuracy of the model predictions. Agreement between experimental data and predicted values of engine performance and NOx emissions levels was good.

In this study, a set of performance and emissions data, obtained from a single-cylinder divided-chamber automotive diesel engine over the normal engine operating range, is described and analyzed. The data are used to evaluate a computer simulation of the engine's operating cycle, described in a companion paper, which predicts the properties of gases inside the engine cylinder throughout the cycle, and engine efficiency, power and NOx emissions. Satisfactory agreement between predictions and measurements is obtained over most of the engine's operating range. The characteristics of the experimental pre- and main-chamber pressure versus crank angle data are then examined in detail. A heat release analysis appropriate for divided-chamber diesel engines is developed and used to obtain heat release rate profiles through the combustion process.

A computer simulation of the four-stroke spark-ignition engine cycle has been used to examine the effects of turbocharging and reduced heat transfer on engine performance, efficiency and NOx emissions. The simulation computes the flows into and out of the engine, calculates the changes in thermodynamic properties and composition of the unburned and burned gas mixtures within the cylinder through the engine cycle due to work, heat and mass transfers, and follows the kinetics of NO formation and decomposition in the burned gas. The combustion process is specified as an input to the program through use of a normalized rate of mass burning profile. From this information, the simulation computes engine power, fuel consumption and NOx emissions. Wide-open-trottle predictions made with the simulation were compared with experimental data from a 5.7ℓ naturally-aspirated and a 3.8ℓ turbocharged production engine.

A computer simulation of the four-stroke spark-ignition engine cycle has been developed for studies of the effects of variations in engine design and operating parameters on engine performance, efficiency and NO emissions. The simulation computes the flows into and out of the engine, calculates the changes in thermodynamic properties and composition of the unburned and burned gas mixtures within the cylinder through the engine cycle due to work, heat and mass transfers, and follows the kinetics of NO formation and decomposition in the burned gas. The combustion process is specified as an input to the program through use of a normalized rate of mass burning profile. From this information, the simulation computes engine power, fuel consumption and NO emissions. Predictions made with the simulation have been compared with data from a single-cylinder CFR engine over a range of equivalence ratios, spark-timings and compression ratios.

This paper describes the results of experimental and computer simulation studies of the combustion process in the prechamber three-valve stratified-charge engine. Prechamber and main-chamber pressure data and matched computer simulation calculations are used to determine the effects of variations in overall air/fuel ratio, engine speed and load, and prechamber volume and orifice diameter on the parameters which define the combustion process (spark advance for optimum torque, ignition delay, combustion duration), on cylinder pressure diagrams (mean main-chamber pressure, mean pressure difference across the orifice, and cycle-by-cycle pressure fluctuations) and on exhaust emissions. General correlations are derived from the data for the shape of the combustion rate profile and the extent of the combustion duration.

The trade-off between engine operating efficiency and NOx emissions in the prechamber three-valve stratified-charge engine is examined in a series of parametric studies using an improved model developed at M.I.T. (1). Engine geometric, operating, and combustion parameters are varied independently and the effects on brake-specific-fuel-consumption, exhaust temperature and brake-specific-NO observed. Parameters chosen for study are: timing of the start of combustion, overall air-fuel ratio, prechamber air-fuel ratio at the start of combustion, main-chamber combustion duration, prechamber size (prechamber volume and orifice diameter), EGR (in main and prechamber intakes), and load. The results quantify trade-off opportunities amongst these design and operating variables which are available to the engine designer.

In the jet-ignition prechamber stratified-charge spark-ignition engine, the fuel-air mixture at the time of combustion is non-uniform. Instantaneous exhaust mass flow rates and emission concentrations from this engine were measured and used to determine the degree to which this charge stratification persists in the products of combustion immediately downstream of the exhaust valve throughout the exhaust process. In all the cases studied no appreciable variations, during the exhaust process, were detected either in the air-fuel ratio of the exhaust gases as a function of time or in the instantaneous concentrations of CO2, O2 and NOx. The experimentally obtained instantaneous HC and CO concentrations in the exhaust, however, displayed large fluctuations and were used to study the sources of these two pollutants in this engine.

The development of a cycle simulation model for the jet ignition prechamber stratified charge engine is described. Given the engine geometry, load, speed, air-fuel ratios and pressures and temperatures in the two intakes, flow ratio and a suitable combustion model, the cycle simulation predicts engine indicated efficiency and NO emissions. The relative importance of the parameters required to define the combustion model are then determined, and values for ignition delay and burn angle are obtained by matching predicted and measured pressure-time curves. The variation in combustion parameters with engine operating variables is then examined. Predicted and measured NO emissions are compared, and found to be in reasonable agreement over a wide range of engine operation. The relative contribution of the prechamber NO to total exhaust NO is then examined, and in the absence of EGR, found to be the major source of NO for overall air-fuel ratios leaner than 22:1.

Measurements were made of exhaust histories of the following species: unburned hydrocarbons (HC), carbon monoxide, carbon dioxide, oxygen, and nitric oxide (NO). The measurements show that the exhaust flow can be divided into two distinct phases: a leading gas low in HC and high in NO followed by a trailing gas high in HC and low in NO. Calculations of time resolved equivalence ratio throughout the exhaust process show no evidence of a stratified combustion. The exhaust mass flow rate is time resolved by forcing the flow to be locally quasi-steady at an orifice placed in the exhaust pipe. The results with the quasi-steady assumption are shown to be consistent with the measurements. Predictions are made of time resolved mass flow rate which compare favorably to the experimental data base. The composition and flow histories provide sufficient information to calculate the time resolved flow rates of the individual species measured.

Photographic and performance studies with a Rapid Compression Machine at the Massachusetts Institute of Technology have been used to develop insight into the role of mixing in diesel engine combustion. Combustion photographs and performance data were analyzed. The experiments simulate a single fuel spray in an open chamber diesel engine with direct injection. The effects of droplet formation and evaporation on mixing are examined. It is concluded that mixing is controlled by the rate of entrainment of air by the fuel spray rather than the dynamics of single droplets. Experimental data on the geometry of a jet in a quiescent combustion chamber were compared with a two-phase jet model; a jet model based on empirical turbulent entrainment coefficients was developed to predict the motion of a fuel jet in a combustion chamber with swirl. Good agreement between theory and experiment was obtained.